Go Back   UG Community @ Ultimate-Guitar.Com > Search Forums
User Name  
Password
Search:

Showing results 1 to 30 of 500
Search took 0.22 seconds.
Search: Posts Made By: J_W
Forum: Gear Building & Customizing 04-06-2015, 02:08 PM
Replies: 4
Views: 156
Posted By J_W
Unscrew the entire locking nut, you will need to...

Unscrew the entire locking nut, you will need to tune everything again. Reset the fine tuners to the middle of their range and tun the guitar. You're going to eventually run out of range on other...
Forum: Guitar Techniques 04-02-2015, 07:35 PM
Replies: 15
Views: 241
Posted By J_W
If you do unison bends you should definitely...

If you do unison bends you should definitely notice. Sounds horrible unless you compensate by bending the note you shouldn't be bending.
Forum: Electric Guitar 03-16-2015, 03:10 PM
Replies: 9
Views: 443
Posted By J_W
The Edge and Edge pro are the best trems Ibanez...

The Edge and Edge pro are the best trems Ibanez makes.
Forum: Gear Building & Customizing 02-23-2015, 03:19 PM
Replies: 5
Views: 178
Posted By J_W
Before you even think of trem options you'll need...

Before you even think of trem options you'll need to know the exact guitar you're going to use as the project. Not all trem routes are the same and that will be the deciding factor in which options...
Forum: Gear Building & Customizing 02-23-2015, 02:18 PM
Replies: 10
Views: 304
Posted By J_W
You need to put the truss rod back where it was. ...

You need to put the truss rod back where it was. Then you need to have the bridge level and in tune at the same time. If you leveled the bridge and then tuned it it's now likely pulled forward and...
Forum: Electric Guitar 02-05-2015, 07:25 PM
Replies: 10
Views: 300
Posted By J_W
Reading on Jemsite, an OFR should be a direct...

Reading on Jemsite, an OFR should be a direct replacement for the lo-trs. Which makes sense since the Edge 3 is also a direct swap for an OFR or a Edge Pro.

So you should be good to go with...
Forum: Electric Guitar 02-05-2015, 07:13 PM
Replies: 10
Views: 300
Posted By J_W
Found this on an Ibanez site. on IBANEZ...

Found this on an Ibanez site.

on IBANEZ EDGE-III cavity:

Ibanez Edge into Edge-III cavity: NO

Ibanez Lo-Pro Edge into Edge-III cavity: NO

Ibanez Edge-Pro into Edge-III cavity: YES
Forum: Electric Guitar 02-05-2015, 04:48 PM
Replies: 10
Views: 300
Posted By J_W
I have used both and honestly both are great. My...

I have used both and honestly both are great. My 1570 has an Edge Pro and I think I may like the feel of it better. You can't go wrong either way.
Forum: Electric Guitar 02-05-2015, 03:28 PM
Replies: 10
Views: 300
Posted By J_W
The Edge Pro and Original Floyd Rose both fit the...

The Edge Pro and Original Floyd Rose both fit the Edge 3 cavity.
Forum: Guitar Gear & Accessories 02-03-2015, 04:36 PM
Replies: 8
Views: 175
Posted By J_W
I love mine, but I keep it in Eb and have other...

I love mine, but I keep it in Eb and have other hardtail guitars I can play in other tunings.
Forum: Guitar Gear & Accessories 02-03-2015, 04:03 PM
Replies: 8
Views: 175
Posted By J_W
Not a good idea to get a guitar with a Floyd if...

Not a good idea to get a guitar with a Floyd if you want to change tunings. You can't change tuning with the fine tuners. You need to adjust your springs for each tuning in order for the trem to...
Forum: Electric Guitar 01-30-2015, 07:27 PM
Replies: 25
Views: 997
Posted By J_W
You can't just go tightening the springs, if you...

You can't just go tightening the springs, if you do that it pulls the trem back. It needs to sit level to work properly. The string buzzing is probably because you're trem isn't set up properly. ...
Forum: Electric Guitar 12-18-2014, 07:22 PM
Replies: 5
Views: 375
Posted By J_W
I wouldn't put that pickup in anything ever, the...

I wouldn't put that pickup in anything ever, the INF pickups are muddy. I doubt it's going to be an improvement over anything.
Forum: Electric Guitar 12-10-2014, 02:16 PM
Replies: 2
Views: 262
Posted By J_W
You need to check the intonation. Google it,...

You need to check the intonation. Google it, there are many tutorials available online.
Forum: Electric Guitar 12-09-2014, 08:26 PM
Replies: 89
Views: 1,584
Posted By J_W
When ever I see someone relic a nice guitar it...

When ever I see someone relic a nice guitar it hurts my soul. Just not my style, I like my guitars looking nice, but who am I to tell anyone what to do with their gear. I don't like them, but hey...
Forum: Gear Building & Customizing 11-24-2014, 04:57 PM
Replies: 15
Views: 1,008
Posted By J_W
I won't lie, after looking at the before pics and...

I won't lie, after looking at the before pics and reading about the intonation issues I thought this was a failed project in the making. To my surprise, it turned out great. Hope it plays as good...
Forum: Electric Guitar 11-20-2014, 03:33 PM
Replies: 28
Views: 752
Posted By J_W
My RGR1570 Prestige, sure it's on the lower end...

My RGR1570 Prestige, sure it's on the lower end of the Prestige line, but it plays as good or better than any guitar I've ever put my hands on and that's a lot of guitars.
Forum: Electric Guitar 11-20-2014, 12:46 PM
Replies: 8
Views: 187
Posted By J_W
Jacks don't really go bad, they just develop bad...

Jacks don't really go bad, they just develop bad connections mostly from getting loose and twisting. I would just pull it out and solder it better. .
Forum: Gear Building & Customizing 11-20-2014, 12:27 PM
Replies: 13
Views: 374
Posted By J_W
The truss rod isn't going to do anything to the...

The truss rod isn't going to do anything to the neck angle. It only adjusts the bow in the neck, that's not going to help you. Since it's a one piece guitar, you're going to have to recess the...
Forum: Electric Guitar 11-19-2014, 06:19 PM
Replies: 8
Views: 187
Posted By J_W
Most likely the jack.

Most likely the jack.
Forum: Gear Building & Customizing 11-19-2014, 03:26 PM
Replies: 4
Views: 205
Posted By J_W
I wouldn't go through the trouble. I would spend...

I wouldn't go through the trouble. I would spend 5 bucks on strings and set it up right.
Forum: Guitar Gear & Accessories 11-17-2014, 08:39 PM
Replies: 51
Views: 1,470
Posted By J_W
I had a V3m for a few months, it's really not...

I had a V3m for a few months, it's really not that heavy sounding without a boost. I used a TS in front and a MXR 10 band EQ in the loop and that helped a ton. There was something I just could not...
Forum: Electric Guitar 11-17-2014, 07:43 PM
Replies: 83
Views: 3,285
Posted By J_W
That and his songs are like someone making a joke...

That and his songs are like someone making a joke about bad metal.
Forum: Gear Building & Customizing 11-17-2014, 06:29 PM
Replies: 4
Views: 205
Posted By J_W
Minus the high E? As in you are playing a 5...

Minus the high E? As in you are playing a 5 string guitar? If this is the case, adjust nothing until you have 6 strings on the guitar. You do not adjust trems for missing strings. lol
Forum: Electric Guitar 11-14-2014, 01:54 PM
Replies: 1
Views: 196
Posted By J_W
Well, the RGT320Q didn't come with that trem, so...

Well, the RGT320Q didn't come with that trem, so I assume it's a 320Z which changed to the Edge Zero in 2008 and is the replacement for the 320Q. Hard to believe it's brand new since it was...
Forum: Electric Guitar 11-12-2014, 04:41 PM
Replies: 18
Views: 804
Posted By J_W
Love this guitar, of course I'd like it better...

Love this guitar, of course I'd like it better with an Edge trem but that thing is nice. Good playing too.
Forum: Electric Guitar 11-12-2014, 01:56 PM
Replies: 6
Views: 185
Posted By J_W
It's completely stripped. You or someone cross...

It's completely stripped. You or someone cross threaded it screwing the bar in. Aside from replacing the bar, you can get a thread die in the correct size and try to re thread the arm at the end...
Forum: Electric Guitar 11-12-2014, 01:46 PM
Replies: 7
Views: 202
Posted By J_W
You can order a new one, just google it. Floyd...

You can order a new one, just google it. Floyd Rose tremolo arm mounting socket or collar.
Forum: Guitar Gear & Accessories 11-11-2014, 07:32 PM
Replies: 25
Views: 894
Posted By J_W
I set my delay to just enough to sustain more but...

I set my delay to just enough to sustain more but not sound like it's repeating. Makes leads sustain way more.
Forum: Electric Guitar 11-05-2014, 03:02 PM
Replies: 17
Views: 555
Posted By J_W
The J Craft stickers came after they started the...

The J Craft stickers came after they started the Prestige's and it should say Prestige on the front of the headstock. It looks like a 1570 but who knows.
Showing results 1 to 30 of 500

 
Forum Jump

All times are GMT -4. The time now is 03:30 PM.

Forum Archives / About / TOS / Advertise with us / Customer Support / Ultimate-Guitar.Com © 2015
Powered by: vBulletin Version 3.0.9
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.