#1
Everyone on the forum keeps telling me to replace my amp. I'm not going to do so. It may not be the best amp in the world, but I deem it as acceptable, so instead of replacing it, I'd like to know if anyone has any ideas on how I could mod it.

It's a Raven RG60 1x12''

To anyone that wishes to post here, actually answer the question.
#2
What specifically are you trying to achieve by modding your amplifier?

With all due respect, this looks more like an act of defiance against the popular opinion rather than an attempt to solve problems through modding. If you like it, it doesn't matter what anyone else thinks.
#3
People keep telling you to replace the amp because modding it will do very little to make the amp sound any better. I know last night you were asking about putting a new speaker in it. Spending money on a new speaker for your amp is like putting a brand new interior and paint job on a car that does not run.
Honestly, I am with Sashki in that it seems like you are now just wanting to mod it to go against what people have suggested. Its gona waste and cost you a lot of money in the end.
#4
You've got a couple problems with this endeavor. First, Raven isn't fond of giving out their schematics. They don't really expect their amps to go in to a repair shop since they are so cheap and most techs wouldn't touch them.

Second, most amps in this price range use surface mount components. This makes it very hard to work on. I can't confirm this second one because I haven't had a Raven come into my shop, and Google isn't giving me any relevant information.

Finally, there is the problem that you will inevitably outgrow the mods. It may sound better than it does right now, but you'll quickly find that you're (pardon the expression) polishing a turd.
#5
Quote by Omni-Virus
Everyone on the forum keeps telling me to replace my amp. I'm not going to do so. It may not be the best amp in the world, but I deem it as acceptable, so instead of replacing it, I'd like to know if anyone has any ideas on how I could mod it.

It's a Raven RG60 1x12''

To anyone that wishes to post here, actually answer the question.


Save your money. I am not trying to steer you in the wrong direction. Leave the speaker alone.

One thing you could do to help your situation might be to buy a PODhd and run it through the fx loop as a preamp. You'd be using the raven for a power amp at that point. It would be like have 12 new amps. (Does it have an FX loop?)

Seriously don't invest any money in your amp. As others have said you really will outgrow it. Glad you like the sound right now.


To upgrade your practice amp- you'd be looking at upgrading the components. Capacitors, resistors being the biggest. You really would just be replacing them with tighter values unless you could get a schematic and have someone suggest some values to change the tone.

Big thing is that you have not said what you are after in your tone. You just want to change it... doesn't help at all. Then you say you can't even change a speaker in your other thread......

Save your money.
Quote by DeathByDestroyr
See, it's important that people clarify when they say "metal", because I pretty much always assume they are a Cannibal Corpse fanboi.
Last edited by R45VT at Oct 15, 2012,
#6
Quote by Omni-Virus
Everyone on the forum keeps telling me to replace my amp. I'm not going to do so. It may not be the best amp in the world, but I deem it as acceptable, so instead of replacing it, I'd like to know if anyone has any ideas on how I could mod it.

It's a Raven RG60 1x12''

To anyone that wishes to post here, actually answer the question.


If its acceptable why would you want to mod it?
I don't give a shit if you listen to me or not
#7
It does good with sound but overall there's slight changes I want to make with my tone. More smooth punch and clarity mainly (not too much more clarity, but a bit more would be nice). I like the amp's equalizer and preamp so I figured the speaker's response and range would be the next best thing. I heard that one guy replaced his speaker with greenbacks or vintage 30s, I forget which, but then he said it sounded much better. I'm into warm sounds like jazz, blues, fusion, funk, shred/instrumental and heavy metal/neo-classical/nu-metal. I heard the celestion gt12 75 would be around what I'm looking for tone-wise as far as speakers go, and I heard a good speaker really can make a good difference in tone. I originally wanted to change pickups, but realized that my input isn't the problem but the output.
#8
Use it as a amp head and get yourself a good cabinet. I am going to be doing this with a Fender Frontman 15 when I get one, just waiting for one to pop up on CL near me for $20 - $30.
Last edited by Darkdevil725 at Oct 15, 2012,
#9
Its a waste I say still, but you don't seem to think our experience counts for anything Have fun. The money you're going to spend on a speaker could go towards a proper amp.

Quote by Darkdevil725
Use it as a amp head and get yourself a good cabinet. I am going to be doing this with a Fender Frontman 15 when I get one, just waiting for one to pop up on CL near me for $20 - $30.


I... I don't even know what to say to this.
I don't give a shit if you listen to me or not
#10
Quote by Kevin Saale



I... I don't even know what to say to this.





If you want to know why, its because I can.
#11
Quote by Darkdevil725


If you want to know why, its because I can.


Ok, I was hoping there wasn't some master plan here or something
I don't give a shit if you listen to me or not
#12
Quote by Omni-Virus
Everyone on the forum keeps telling me to replace my amp. I'm not going to do so. It may not be the best amp in the world, but I deem it as acceptable, so instead of replacing it, I'd like to know if anyone has any ideas on how I could mod it.

It's a Raven RG60 1x12''

To anyone that wishes to post here, actually answer the question.

So wait...

Your amp is:
A. Acceptable
B. In need of modding

Our opinions are:
A. Wrong
B. Needed

You only get to pick one of each...
Quote by Cathbard
Quote by Raijouta
Unless its electronic drums.

BURN THE WITCH!!!!!
#13
Well... you could replace all the caps with higher quality ones in attempts to improve clarity, and then maybe lower the input impedance for more gain if that's something you fancy.
But in all honesty if you're not entirely happy with the tone of your amp and it's not considered very good in general by most (I don't have experience of your amp) then I wouldn't waste my time. As much as you don't want to hear it, you'd be better off saving up and getting a better amp. Then you can mod the **** out of your old one into firewood or something.
Last edited by NotTheMessiah30 at Oct 15, 2012,
#14
there are no mods available for that amp.
Call me "Shot".

ShotRod Guitar Works

Custom Hand-wired Amplifiers and Effect Pedals.

Est. 2007


Source to everything I say about Guitars, Pedals, and Amplifiers: I make them.


UG's Best DIY PedalBoard
#15
Someone recommend me a 1x12" combo amp that has 2 channels. Clean channel must do warm jazz tones. Drive channel must do chunky, punchy, smooth, and warm metal. Make it not break the bank. Provide videos or sound clips. Keep in mind I'm using a basswood guitar with tone zone in the bridge and regular norton in the neck. If you can't do this then recommend the next best thing, being either a mod to my amp or a new cab or a new speaker or new pickups.
#16
And I know someone here is gonna be a tube purist so I'd prefer if you recommend me a tube amp.
#17
Quote by Omni-Virus
Someone recommend me a 1x12" combo amp that has 2 channels. Clean channel must do warm jazz tones. Drive channel must do chunky, punchy, smooth, and warm metal. Make it not break the bank. Provide videos or sound clips. Keep in mind I'm using a basswood guitar with tone zone in the bridge and regular norton in the neck. If you can't do this then recommend the next best thing, being either a mod to my amp or a new cab or a new speaker or new pickups.


I'm glad I don't work in a guitar store, especailly one near you haha.
Not being funny but it seems like there'd be a fair bit of research involved in that, and why should we be doing that on your behalf?

Although from all that I would probably just go ahead and say get a modelling amp of some kind since you have quite a specific yet varied range of tones you're after. I hear good things about the Peavey Vypyr, so maybe go give one a try.
Last edited by NotTheMessiah30 at Oct 15, 2012,
#18
I'll second the Peavey Vyper as a step up from the Raven at a low cost. That being said, I'm pretty out of the loop on what's currently in production. Perhaps you should ask that particular question in GG&A.
#21
Despite actually working in a music shop, my knowledge is limited. I stick to fixing the broken ones. I'm not a salesman.

So, I strongly recommend you look at GG&A (https://www.ultimate-guitar.com/forum/forumdisplay.php?f=33). Having said that, look at an Egnater Rebel 30 if you're so against modelling. Honestly though, the Vyper 60 has a tube output section and sounds pretty good for the price.
Last edited by end_citizen at Oct 15, 2012,
#22
Quote by end_citizen
Despite actually working in a music shop, my knowledge is limited. I stick to fixing the broken ones. I'm not a salesman.

So, I strongly recommend you look at GG&A (https://www.ultimate-guitar.com/forum/forumdisplay.php?f=33). Having said that, look at an Egnater Rebel 30 if you're so against modelling. Honestly though, the Vyper 60 has a tube output section and sounds pretty good for the price.


x10 and then some. Nail on the head.
Quote by DeathByDestroyr
See, it's important that people clarify when they say "metal", because I pretty much always assume they are a Cannibal Corpse fanboi.
#23
In all honesty i think the TS wants the moon on a stick. Having such specific requirements in mind and wanting to do it on a budget just isn't realistic. It's tantamount to saying I want a guitar that plays and sounds like a £2000 ESP or PRS but i only want to spend £600 and it must do xyz on top.
#24
Let me get this straight. You're asking how to do it off the very people that told told you not to do it?
If you were my apprentice you'd be spending a day trapped under the floor. Seriously, man - wtf?
Gilchrist custom
Yamaha SBG500
Telecasters
Randall RM100 & RM20
Marshall JTM45 clone
Marshall JCM900 4102 (modded)
Marshall 18W clone
Fender 5F1 Champ clone
Atomic Amplifire
Marshall 1960A
Boss GT-100


Cathbard Amplification
My band
#26
Quote by Omni-Virus
Someone recommend me a 1x12" combo amp that has 2 channels. Clean channel must do warm jazz tones. Drive channel must do chunky, punchy, smooth, and warm metal. Make it not break the bank. Provide videos or sound clips. Keep in mind I'm using a basswood guitar with tone zone in the bridge and regular norton in the neck. If you can't do this then recommend the next best thing, being either a mod to my amp or a new cab or a new speaker or new pickups.

You are a real piece of work...
Quote by Cathbard
Quote by Raijouta
Unless its electronic drums.

BURN THE WITCH!!!!!
#27
whose bank is this not supposed to break. yours or mine?

buffalo buffalo buffalo buffalo buffalo buffalo buffalo.
#28

What I have read so far. I wish to directly contradict everything you have just advised me to do, what would be the best way of doing that? Failing that can I get a 2 channel jazz/metal amp for 200 without modeling?
Quote by R45VT
Bastards.