#1
ok so far it looks like i have everything i need to install them.

BUT THERE SEEMS TO BE ONE FINAL PROBLEM!

here is the pdf instructions for installing them: http://www.seymourduncan.com/images/products/electric/humbuckers/501020-110.pdf

My case is the "2 volume, 2 tone" scenario

the ONLY thing that is bugging me is the wire coming out of the far end of the 3-way toggle switch (not the one with three wires connected.

Here is a picture of an SG cavity i found on the internet, it is of an SG juior but the 3-way switch is pretty much the same:

http://i249.photobucket.com/albums/gg234/bostonguitarrepair/1965%20SG%20Junior/IMG_4925.jpg

how do i put in that third cable (it is the one that goes from the 3-way toggle to the "bridge volume 25k" thing

thanks

EDIT : Link to cavity pic fixed
B-52 OWNERZ LINK!!!

GUITAR
Gibson SG Special Faded Brown w/ Duncan Blackouts
AMP
B-52 At-112 60 Wat All Tube Combo
PEDALS
MXR 108 10 Band EQ
ISP Noise Gate
SETUP
SG --> MXR --> ISP --> B-52
Last edited by gpowsang at Dec 27, 2008,
#3
It's just the ground wire for the switch. Connect the case of the switch to the case of the pot.
#4
^my problem is that there are only three wires coming out from one side of my 33-way switch
B-52 OWNERZ LINK!!!

GUITAR
Gibson SG Special Faded Brown w/ Duncan Blackouts
AMP
B-52 At-112 60 Wat All Tube Combo
PEDALS
MXR 108 10 Band EQ
ISP Noise Gate
SETUP
SG --> MXR --> ISP --> B-52
#5
anyone please?

this is my last problem before i can install them

thanks
B-52 OWNERZ LINK!!!

GUITAR
Gibson SG Special Faded Brown w/ Duncan Blackouts
AMP
B-52 At-112 60 Wat All Tube Combo
PEDALS
MXR 108 10 Band EQ
ISP Noise Gate
SETUP
SG --> MXR --> ISP --> B-52
#6
Yep. So just solder another wire from the case of your switch to the case of your pot where your other grounds are soldered. That's all the wire in the diagram is telling you to do.
#7
wats the case...sorry im a noob when it comes to guitar electronics
B-52 OWNERZ LINK!!!

GUITAR
Gibson SG Special Faded Brown w/ Duncan Blackouts
AMP
B-52 At-112 60 Wat All Tube Combo
PEDALS
MXR 108 10 Band EQ
ISP Noise Gate
SETUP
SG --> MXR --> ISP --> B-52
#8


The bit outlined in red is the case. The container for the switch that doesn't touch the terminal contacts.
#9
umm my 3-way switch looks way different

look at the pic
B-52 OWNERZ LINK!!!

GUITAR
Gibson SG Special Faded Brown w/ Duncan Blackouts
AMP
B-52 At-112 60 Wat All Tube Combo
PEDALS
MXR 108 10 Band EQ
ISP Noise Gate
SETUP
SG --> MXR --> ISP --> B-52
#10
Yes it is a different switch. The picture was to illustrate the text. The case of the switch needs to be grounded. The case is the metal part of the switch that protrudes above the pickguard (and continues below) that isn't in contact with the three terminals. Any part of that is fine.
#11
^thanks for the reply

i get it now.

so in my case i would solder the raindrop looking section?
B-52 OWNERZ LINK!!!

GUITAR
Gibson SG Special Faded Brown w/ Duncan Blackouts
AMP
B-52 At-112 60 Wat All Tube Combo
PEDALS
MXR 108 10 Band EQ
ISP Noise Gate
SETUP
SG --> MXR --> ISP --> B-52